my profile | my password | search | faq & rules | forum home

» Film-Tech Forum ARCHIVE   » Operations   » Film Handlers' Forum   » How to tell where these scratches came from? (Page 1)

This topic comprises 2 pages: 1  2

Author Topic: How to tell where these scratches came from? Jesse Skeen Phenomenal Film Handler Posts: 1517 From: Sacramento, CA Registered: Aug 2000 posted 06-12-2001 05:24 AM                     At a few different theaters I've seen prints get scratched in ways I can never figure out- most confusing is scratches on the emulsion side that sort of look like diagonal platter scratches, except they're not visible across the entire frame and part of them is green. When projected, these look like there's a flashing green dash moving upwards on the screen. (I've seen this both with Christie and Strong platters). Another type of scratch I've seen done with Strong platters is a thin vertical line on the base side, and that line is made up of diagonal scratches. I know this is caused by misthreading because it doesn't happen on every film, but I don't know what to tell the people doing it because I can't tell what's causing it. One other that's got me stumped is diagonal scratches only on the far right-hand side of the picture- you'd suspect this happened during film make-up but it happens afterwards. It once took me catching someone in the act to figure out where some scratches were coming from- I came in once and saw a green vertical scratch on the screen, then checked the Christie platter and saw someone had threaded under one of the rollers, dragging the film along the screw underneath- ouch!  |  IP: Logged Roger Frazee Film Handler Posts: 16 From: Knoxville, TN, USA Registered: Nov 2000 posted 06-12-2001 06:15 AM                     I have found that diagonal scratches are often caused by misaligned guidance rollers. If film does not lay flat in the roller as it enters and exits, it will rub across the roller as it travels over it. In severe cases it can even ride up on the roller flange. This is why it is essential to check the roller alignment each time the projector is threaded.  |  IP: Logged Jerry Chase Phenomenal Film Handler Posts: 1068 From: Margate, FL, USA Registered: Nov 2000 posted 06-12-2001 08:04 AM                       Jesse, I think you have the core of a great idea. I would love to see snips of damaged film and an accompanying photo of the cause of the damage, along with a written explanation of how the damage is caused and how it can be prevented. I imagine this could be something where Kodak might even produce a booth chart for distribution to theatres. How about it J.P.? Think something like this would fly? A chart like this could educate a lot of booth jockeys (and managers) fast and possibly prevent a lot of film damage.  |  IP: Logged Dustin Mitchell Phenomenal Film Handler Posts: 1865 From: Mondovi, WI, USA Registered: Mar 2000 posted 06-12-2001 08:21 AM                     Roger's absolutely right, roller alignment is the source of many scratches. The scratches on the far right side of the screen you mentioned Jesse sound just like a problem we had at my theatre for a while. The source of the problem-discovered after many damaged prints-was misaligned rollers.  |  IP: Logged Brad Miller Administrator Posts: 17775 From: Plano, TX (36.2 miles NW of Rockwall) Registered: May 99 posted 06-12-2001 12:55 PM                     Jesse, the first scratch you described can actually be caused by a loop scratch from making the lower loop too big on a Christie (they now have scratch guards installed on all projectors). The other ones you have described sound like that last roller is too close to the takeup deck. Do the scratches get worse and worse as time goes by? If so, you have a roller that is out of alignment. If they just appear and then never get worse, odds are it was an operator threading error. Don't forget to check the two magazine rollers on the projector too.  |  IP: Logged Jesse Skeen Phenomenal Film Handler Posts: 1517 From: Sacramento, CA Registered: Aug 2000 posted 06-13-2001 05:57 AM                     I'm pretty sure all of this is being caused by misthreading, and not problems with the actual equipment, since it doesn't always happen on the same projector on every film, and it tends to happen on days when I'm not there. (I don't claim to be perfect, but since the time I scratched a print during one of my very first shifts 9 years ago, I haven't knowingly scratched one since!) Having photos on hand is a great idea, I've already been looking for a Polariod to borrow so I can mis-thread all the ways I know how and take pictures so the newer people can be sure not to do it.  |  IP: Logged Gordon McLeod Film God Posts: 9532 From: Toronto Ontario Canada Registered: Jun 99 posted 06-13-2001 10:05 AM                     I have noticed that often diagonal scratchs are caused by people misthreading a roller and haveing the film sitting up on the flange and the keeper holding it in place Also on the older Specos the film getting folder into the split of the rollers the cure Check and Double check  |  IP: Logged Joe Redifer You need a beating today Posts: 12859 From: Denver, Colorado Registered: May 99 posted 06-13-2001 12:59 PM                        The Strong scratches you describe are caused by misthreading the brain so that the film is actually riding AROUND one of the rollers that surround the payout AFTER the film leaves the payout arm itself. This will cause your black line that is made up of smaller diagonal scratches. We had this type of scratch once and I was blamed, so I had to prove that I didn't do it by scratching test film. I proved that it wasn't me since the first guy who noticed it threaded it up. I had also watched the previous show in that auditorium and it was fine. Ha!  |  IP: Logged Tom Kroening Expert Film Handler Posts: 214 From: Janesville, WI USA Registered: Oct 1999 posted 06-13-2001 04:56 PM                     I've seen green diagonal scratches caused by misthreading the platter. It usually occurs when your rewind platter is above your payout platter. Many new projectionists like to go from the brain to the first roller and straight up instad of going down to keep the tension on that first roller. This allows the film to be rubbing on the bottom of the rewind platter as it goes around. As this is only one possible cause for scratching, your best bet is to go through and retrain your staff. Make sure they are consistant with their loop sizes, and always always make them check and recheck when they start the film. I make it a point to teach people to run though all the projectors again after the last show of the set is started.  |  IP: Logged John Pytlak Film God Posts: 9987 From: Rochester, NY 14650-1922 Registered: Jan 2000 posted 06-13-2001 07:44 PM                        Roger Frazee is correct: Short horizontal or slightly diagonal scratches are usually caused by the film riding up on the flange of a guidance roller. Each revolution of the roller usually produces a scratch at a burr or rough spot. The distance between scratches (the circumference of the roller) is so regular that the scratches seem to march up or down the screen in a regular pattern. Always check to be sure the film is riding "true" on every roller, and that all rollers are turning. ------------------ John P. Pytlak, Senior Technical Specialist Worldwide Technical Services, Entertainment Imaging Eastman Kodak Company Research Labs, Building 69, Room 7419 Rochester, New York, 14650-1922 USA Tel: 716-477-5325 Cell: 716-781-4036 Fax: 716-722-7243 E-Mail: john.pytlak@kodak.com Web site: http://www.kodak.com/go/motion  |  IP: Logged Robb Johnston Expert Film Handler Posts: 147 From: St. Louis Suburbs Registered: Nov 1999 posted 06-14-2001 12:17 AM                        The rising green dash sounds alot like a scratch I had a few weeks back. What Projector do you use? I had the problem on a Simplex 1050. The Friction roller on the Lateral guide assembly of the Sound head was about 12 years old, and had started to crack on the edge. When the crack worked it's way to the surface it made a superficial pin hole scratch into the emulsion. Unfortunately, it was so slight that it was black on screen, but traveled up the picture, and I spent days checking for a burr scratching the base side. It didn't get deep enough to be a green scratch until it ran for a number of days and it had scratches on top of scratches.  |  IP: Logged Ken Lackner Phenomenal Film Handler Posts: 1907 From: Atlanta, GA, USA Registered: Sep 2001 posted 09-18-2001 08:49 PM                     I have seen scratches that look like green dots going straight up the screen vertically, not diagonaly. I have never been able to figure these out. Anyone?  |  IP: Logged Brad Miller Administrator Posts: 17775 From: Plano, TX (36.2 miles NW of Rockwall) Registered: May 99 posted 09-18-2001 11:27 PM                     Loop scratches from making a loop too big.  |  IP: Logged Ken Lackner Phenomenal Film Handler Posts: 1907 From: Atlanta, GA, USA Registered: Sep 2001 posted 09-18-2001 11:47 PM                     Gottcha. I can picture how that could happen. But why doesn't the same part of each frame get scratched? Why does the scratch travel up the picture?  |  IP: Logged Aaron Sisemore Flaming Ribs beat Reeses Peanut Butter Cups any day! Posts: 3061 From: Rockwall TX USA Registered: Sep 1999 posted 09-19-2001 12:33 AM                     A burr or other sharp part of a roller that makes direct contact with the image area of the film (sound head impedance drums come to mind) can also cause the little green dot scratches. Usually taked 2-3- passes thru the machine to look like they crawl up/down the screen. Either way it needs to be checked out if that is the cause. Aaron  |  IP: Logged

All times are Central (GMT -6:00)

This topic comprises 2 pages: 1  2

Printer-friendly view of this topic

Hop To: Select a Forum: Category: Operations -------------------- Digital Cinema Forum Film Handlers' Forum Large Format Forum Ground Level Feature Info, Trailer Attachments & REAL Credit Offsets Category: Community -------------------- Film-Yak Film Handlers' Movie Reviews The Afterlife Bob Maar's Joke-A-Thon Category: Classified -------------------- Equipment and Supplies Wanted/For Sale Help Wanted/Seeking Employment Category: System -------------------- Software Beta Testing Forum

The Film-Tech Forums are designed for various members related to the cinema industry to express their opinions, viewpoints and testimonials on various products, services and events based upon speculation, personal knowledge and factual information through use, therefore all views represented here allow no liability upon the publishers of this web site and the owners of said views assume no liability for any ill will resulting from these postings. The posts made here are for educational as well as entertainment purposes and as such anyone viewing this portion of the website must accept these views as statements of the author of that opinion and agrees to release the authors from any and all liability.