my profile | my password | search | faq & rules | forum home

» Film-Tech Forum ARCHIVE   » Operations   » Film Handlers' Forum   » My xenon won't light!!

Author Topic: My xenon won't light!! Scott Balko Expert Film Handler Posts: 136 From: Redwood Falls, Minnesota, USA Registered: Apr 2000 posted 05-12-2001 05:19 PM                     I've got a Xetron 2000 watt lamphouse (I think it's XH-2000 or something) and I'm getting the spark from the starter in the bulb but it won't hold the arc. I've got the correct voltage out of the power supply. What is the first thing to check, then what, etc., etc..... Thanks in advance. Signed: A very novice xenon user  |  IP: Logged John Walsh Film God Posts: 2490 From: Connecticut, USA, Earth, Milky Way Registered: Oct 1999 posted 05-12-2001 05:42 PM                     Is DC getting to the bulb? There are two power sources (the lamphouse, which powers the fan and ingiter) and the rectifier which supplies the DC. Perhaps the bulb is no longer air tight, and the gas has excaped?  |  IP: Logged Aaron Sisemore Flaming Ribs beat Reeses Peanut Butter Cups any day! Posts: 3061 From: Rockwall TX USA Registered: Sep 1999 posted 05-12-2001 07:39 PM                     OK-You say that the DC is getting to the lamphouse, next question is how much? No-load (before the bulb strikes) DC voltage should be in excess of 100 VDC for a 2000W lamp. If its anything less, you may have some power supply problems. Next thing to check is to try another KNOWN TO BE GOOD xenon bulb. If that one strikes and runs then obviously you had a bum bulb to start with. Aaron  |  IP: Logged Gordon McLeod Film God Posts: 9532 From: Toronto Ontario Canada Registered: Jun 99 posted 05-12-2001 08:23 PM                     Also it is possible for the boost supply of the rectifier to exist but the main supply to have a bad diode and not be able to deliver the main current after the zap measure the voltage as well Before the lamp lights it should be between 75-100 volts After ignition it should be 21-28 volts  |  IP: Logged Marc Jones Film Handler Posts: 82 From: Elizabethtown, KY Registered: Jun 99 posted 05-13-2001 12:03 AM                     I have had problems with the connections on the bulb loose or I have had seen some that have arc inside of the connecter. Good luck  |  IP: Logged John Walsh Film God Posts: 2490 From: Connecticut, USA, Earth, Milky Way Registered: Oct 1999 posted 05-13-2001 09:45 AM                     Scott; Is that the XH-2000 lamphouse and N3-X50 power supply?  |  IP: Logged Scott Balko Expert Film Handler Posts: 136 From: Redwood Falls, Minnesota, USA Registered: Apr 2000 posted 05-13-2001 10:05 PM                     John, yeah it is. I know that the power supply by the numbers doesn't match up with the lamphouse, although the supply has been equipped with small fans to cool it. According to the guages I'm putting out enough current to run 1850 watts. Anyway, before I go too far, I tried a known good bulb and it works just fine. Like the saying goes, "Keep it simple, stupid."  |  IP: Logged Randy Stankey Film God Posts: 6539 From: Erie, Pennsylvania Registered: Jun 99 posted 05-13-2001 10:13 PM                     When I get a lamp that won't strike I do the following: Check the interlocks, if any. -- You have done this or else you wouldn't be getting any readings when you check the voltage. Visually check the lamp. -- You have a good lamp. Check the diodes. Check the igniter. Check all the connections in the power supply. Check the contactor(s) and incomming line voltage(s). Try a new lamp. Cuss at it and go have a cup of coffee or something while I think about it.  |  IP: Logged

All times are Central (GMT -6:00)

Printer-friendly view of this topic

Hop To: Select a Forum: Category: Operations -------------------- Digital Cinema Forum Film Handlers' Forum Large Format Forum Ground Level Feature Info, Trailer Attachments & REAL Credit Offsets Category: Community -------------------- Film-Yak Film Handlers' Movie Reviews The Afterlife Bob Maar's Joke-A-Thon Category: Classified -------------------- Equipment and Supplies Wanted/For Sale Help Wanted/Seeking Employment Category: System -------------------- Software Beta Testing Forum

The Film-Tech Forums are designed for various members related to the cinema industry to express their opinions, viewpoints and testimonials on various products, services and events based upon speculation, personal knowledge and factual information through use, therefore all views represented here allow no liability upon the publishers of this web site and the owners of said views assume no liability for any ill will resulting from these postings. The posts made here are for educational as well as entertainment purposes and as such anyone viewing this portion of the website must accept these views as statements of the author of that opinion and agrees to release the authors from any and all liability.